Anritsu S113C Podręcznik Użytkownika Strona 52
- Strona / 120
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Spectrum Analyzer Mode
Selecting Spectrum Analyzer Mode
Step 1. Press the ON/OFF key.
Step 2. Press the MODE key and use the Up/Down arrow key to select Spectrum Ana-
lyzer mode. Press ENTER to set the mode.
Making a Measurement
Step 1.
Connect the input cable to the RF In test port.
Step 2. Locate and display the signal(s) of interest by selecting the desired frequency,
span, and amplitude value.
Selecting the Frequency
Step 1.
Press the FREQ/DIST key to display the Frequency menu.
Step 2. To enter a center frequency, select the
CENTER soft key and enter the desired
center frequency on the keypad. Select the
GHz, MHz, kHz,orHz softkey to ac-
cept the center frequency input.
or
To set a specific frequency band, select the
START soft key and enter the de-
sired start frequency on the keypad. Select the
GHz, MHz, kHz,orHz softkey to
accept the start frequency input. Then select the
STOP soft key and enter the de-
sired stop frequency on the keypad. Select the
GHz, MHz, kHz,orHz softkey to
accept the stop frequency input.
Selecting the Span
Step 1.
Press the FREQ/DIST key to display the Frequency menu.
Step 2. Press the
SPAN soft key to display the Span menu.
Step 3. To set a specific span, enter the desired span on the keypad and select the
GHz,
MHz, kHz,orHz soft key to accept the input.
or
For a full span, select the
FULL soft key. Selecting FULL will override the
START and STOP frequencies set above.
or
For a single frequency measurement, select the
ZERO soft key.
NOTE: To quickly move the span value up or down, select the SPAN UP 1-2-5 or
SPAN DOWN 1-2-5 soft keys. These keys facilitate a zoom-in, zoom-out in a
1-2-5 sequence.
Selecting the Amplitude
Step 1.
Press the AMPLITUDE key.
Step 2. Press the
UNITS soft key and select the desired units from the soft keys pre
-
sented. Press the
BACK soft key to return to the Amplitude menu.
3-9
Chapter 3 Getting Started
- Site Master 1
- S113C, S114C 1
- S331C, and S332C 1
- Antenna, Cable and 1
- Spectrum Analyzer 1
- WARRANTY 3
- LIMITATION OF WARRANTY 3
- TRADEMARK ACKNOWLEDGMENTS 3
- Table of Contents 5
- Chapter 3 - Getting Started 6
- Chapter 6 - Power Measurement 8
- Chapter 7 - Software Tools 8
- Appendix A - Reference Data 8
- Appendix B - Windowing 8
- Chapter 1 9
- General Information 9
- Printers 10
- Optional Accessories 11
- Performance Specifications 12
- Chapter 1 General Information 13
- Preventive Maintenance 14
- Calibration 14
- Annual Verification 15
- ESD Precautions 15
- Chapter 2 17
- Functions and Operations 17
- Front Panel Overview 18
- Function Hard Keys 19
- Keypad Hard Keys 20
- Soft Keys 22
- MODE=DTF: 23
- SOFTKEYS: 23
- FREQ/DIST 23
- AMPLITUDE 23
- MODE=SPECTRUM ANALYZER: 24
- Power Monitor Menu 34
- Self Test 35
- Error Codes 35
- Description 36
- Self Test Error Messages 36
- Range Errors 37
- InstaCal Error Messages 38
- Battery Information 40
- BATTERY INDI 41
- Battery Life 42
- 2-27/2-28 43
- Chapter 3 44
- Getting Started 44
- Site Master Mode 45
- Calibration Verification 46
- Figure 3-2. Calibration Setup 47
- InstaCal Module Verification 48
- Site Master S332C 49
- Setting the Scale 50
- Auto Scale 50
- Amplitude Scale 50
- Spectrum Analyzer Mode 52
- Selecting Sweep Parameters 53
- Adjusting Attenuator Settings 54
- Save and Recall a Setup 55
- Save and Recall a Display 55
- Changing the Units 56
- Changing the Display Language 56
- Adjusting Markers 56
- Adjusting Limits 56
- Setting the System Language 58
- Setting the System Impedance 58
- Printing 59
- Printer Switch Settings 60
- Using the Soft Carrying Case 61
- Chapter 4 62
- Cable & Antenna 62
- Measurements 62
- MODE key 64
- Insertion Loss Measurement 65
- ´ Length (ft) = Loss (dB) 66
- Resolution 70
- MARKER key 71
- 4-11/4-12 72
- Chapter 5 73
- AUTO mode, as the 74
- MANUAL) mode, the 74
- AM/FM Modulation 75
- Frequency Modulation 76
- Field Strength Measurements 78
- Creating a Spectral Mask 79
- EDIT and enter the 80
- EDIT when done 80
- Trace Overlay 81
- Occupied Bandwidth 82
- Channel Power Measurement 84
- GSM Channel Power Measurement 84
- Procedure 85
- Adjacent Channel Power Ratio 87
- Measurement Applications 89
- OUT OF BANDOUT OF BAND 95
- In-band Spurious Measurement 97
- Required Equipment 97
- Field Strength 99
- Antenna Calculations 100
- 5-29/5-30 101
- Power Measurement 102
- Chapter 6 102
- Chapter 7 104
- Software Tools 104
- Installation 105
- Using Software Tools 106
- Plot Capture to the PC 107
- Plot Upload to the Instrument 107
- Plot Properties 107
- Trace Overlay or Plot Overlay 108
- Saving Traces 109
- Creating a Database 110
- Printing Formats 110
- Uploading Antenna Factors 111
- 7-9/7-10 112
- Appendix A 113
- Reference Data 113
- Appendix A Reference Data 114
- Appendix B 116
- Windowing 116
- Appendix B Windowing 117
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Anritsu S113C
(5 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji