Anritsu S113C Podręcznik Użytkownika Strona 40
- Strona / 120
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Battery Information
Charging a New Battery
The NiMH battery supplied with the Site Master has already completed three charge and
discharge cycles at the factory and full battery performance should be realized after your
first charge.
NOTE: The battery will not charge if the battery temperature is above 45° Cor
below 0° C.
Charging the Battery in the Site Master
The battery can be charged while installed in the Site Master.
Step 1. Turn the Site Master off.
Step 2. Connect the AC-DC adapter (Anritsu part number: 40-115) to the Site Master
charging port.
Step 3. Connect the AC adapter to a 120 VAC or 240 VAC power source as appropriate
for your application.
The green external power indicator on the Site Master will illuminate, indicating
the presence of external DC power, the battery charge indicator will light, and
the battery will begin fast charging. The charging indicator will remain lit as
long as the battery is fast charging. Once the battery is fully charged, the fast
charging indicator will turn off and a trickle charge will be started to maintain
battery capacity. If the battery fails to charge, contact your nearest Anritsu ser-
vice center.
NOTE: If a battery is excessively discharged, it may require several hours of
trickle charging before the charger will allow a fast charge. Switching to fast
charge mode is not automatic. You must either cycle the power on and off, or
disconnect and reconnect the AC-DC adapter.
Charging the Battery in the Optional Charger
Up to two batteries can be charged simultaneously in the optional battery charger.
Step 1. Remove the NiMH battery from your Site Master and place it in the optional
charger (Anritsu part number 2000-1029).
Step 2. Connect the lead from the AC-DC adapter to the charger.
Step 3. Connect the AC-DC adapter to a 120 VAC or 240 VAC power source as appro-
priate for your application.
Each battery holder in the optional charger has an LED charging status indicator. The LED
color changes as the battery is charged:
Red indicates the battery is charging
Green indicates the battery is fully charged
Yellow indicates the battery is in a waiting state (see below).
2-24
Chapter 2 Functions and Operations
- Site Master 1
- S113C, S114C 1
- S331C, and S332C 1
- Antenna, Cable and 1
- Spectrum Analyzer 1
- WARRANTY 3
- LIMITATION OF WARRANTY 3
- TRADEMARK ACKNOWLEDGMENTS 3
- Table of Contents 5
- Chapter 3 - Getting Started 6
- Chapter 6 - Power Measurement 8
- Chapter 7 - Software Tools 8
- Appendix A - Reference Data 8
- Appendix B - Windowing 8
- Chapter 1 9
- General Information 9
- Printers 10
- Optional Accessories 11
- Performance Specifications 12
- Chapter 1 General Information 13
- Preventive Maintenance 14
- Calibration 14
- Annual Verification 15
- ESD Precautions 15
- Chapter 2 17
- Functions and Operations 17
- Front Panel Overview 18
- Function Hard Keys 19
- Keypad Hard Keys 20
- Soft Keys 22
- MODE=DTF: 23
- SOFTKEYS: 23
- FREQ/DIST 23
- AMPLITUDE 23
- MODE=SPECTRUM ANALYZER: 24
- Power Monitor Menu 34
- Self Test 35
- Error Codes 35
- Description 36
- Self Test Error Messages 36
- Range Errors 37
- InstaCal Error Messages 38
- Battery Information 40
- BATTERY INDI 41
- Battery Life 42
- 2-27/2-28 43
- Chapter 3 44
- Getting Started 44
- Site Master Mode 45
- Calibration Verification 46
- Figure 3-2. Calibration Setup 47
- InstaCal Module Verification 48
- Site Master S332C 49
- Setting the Scale 50
- Auto Scale 50
- Amplitude Scale 50
- Spectrum Analyzer Mode 52
- Selecting Sweep Parameters 53
- Adjusting Attenuator Settings 54
- Save and Recall a Setup 55
- Save and Recall a Display 55
- Changing the Units 56
- Changing the Display Language 56
- Adjusting Markers 56
- Adjusting Limits 56
- Setting the System Language 58
- Setting the System Impedance 58
- Printing 59
- Printer Switch Settings 60
- Using the Soft Carrying Case 61
- Chapter 4 62
- Cable & Antenna 62
- Measurements 62
- MODE key 64
- Insertion Loss Measurement 65
- ´ Length (ft) = Loss (dB) 66
- Resolution 70
- MARKER key 71
- 4-11/4-12 72
- Chapter 5 73
- AUTO mode, as the 74
- MANUAL) mode, the 74
- AM/FM Modulation 75
- Frequency Modulation 76
- Field Strength Measurements 78
- Creating a Spectral Mask 79
- EDIT and enter the 80
- EDIT when done 80
- Trace Overlay 81
- Occupied Bandwidth 82
- Channel Power Measurement 84
- GSM Channel Power Measurement 84
- Procedure 85
- Adjacent Channel Power Ratio 87
- Measurement Applications 89
- OUT OF BANDOUT OF BAND 95
- In-band Spurious Measurement 97
- Required Equipment 97
- Field Strength 99
- Antenna Calculations 100
- 5-29/5-30 101
- Power Measurement 102
- Chapter 6 102
- Chapter 7 104
- Software Tools 104
- Installation 105
- Using Software Tools 106
- Plot Capture to the PC 107
- Plot Upload to the Instrument 107
- Plot Properties 107
- Trace Overlay or Plot Overlay 108
- Saving Traces 109
- Creating a Database 110
- Printing Formats 110
- Uploading Antenna Factors 111
- 7-9/7-10 112
- Appendix A 113
- Reference Data 113
- Appendix A Reference Data 114
- Appendix B 116
- Windowing 116
- Appendix B Windowing 117
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Anritsu S113C
(5 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji