Anritsu MG3642A Instrukcja Użytkownika Pobierz pdf (Strona 179)

SECTION 7 PERFORMANCE TEST

7-11

(5) Note on test

The demodulation zone of the modulation analyzer must be within 0.3 to 3 kHz at measurement of the modulation

factor and 0.3 to 15 kHz or 0.3 to 20 kHz at measurement of the distortion.

1 2 ... 174 175 176 177 178 179 180 181 182 183 184 ... 211 212

ANRITSU CORPORATION 1
Safety Symbols 2
For Safety 3
Equipment Certificate 7
Anritsu Warranty 7
Anritsu Corporation Contact 7
Notes On Export Management 8
CE Conformity Marking 10
4. Authorized representative 11
C-tick Conformity Marking 12
Power Line Fuse Protection 13
SECTION 1 19
1.2 Operation Manual 20
1.3 Composition of Devices 21
1.3.2 Options 22
Table 1-3. Options 22
1.4 Application Parts 23
1.5 Specifications 24
Specifications (continued) 25
(0 to 50°C) 29
■ Option 22 (FSK encoder) 29
SECTION 1 GENERAL 30
SECTION 2 31
PRECAUTION 31
CAUTION 32
SECTION 2 PRECAUTION 33
WARNING CAUTION 34
WARNING 35
SECTION 3 37
PANEL LAYOUT 37
SECTION 3 PANEL LAYOUT 38
3.1.2 Rear panel layout 39
3.1.3 Panel layout diagram 40
Fig. 3-2. Rear Panel 40
Fig. 3-1. Front Panel 40
OPERATING INSTRUCTIONS 41
SECTION 4 41
4.1.1 Turning Power On 43
4.1.2 Turning Power Off 44
4.2 Explanation of Screens 45
Chk SysGPIB Opt Trig 46
Main Menu (2/2) 46
[Preset] key 46
MG3641A/MG3642A front panel 46
4.4 Setting the Frequency 48
[Rel Freq] key 49
[Shift] key 49
4.4.3 Frequency Offset 50
[Level] key 51
[Rel Level] key 52
4.5.3 Output Level Offset 53
4.5.4 Level Continuous Mode 54
[RF Off/On] key 55
Chk SysGPIB Opt Trig 57
4.6 Setting the Modulation 58
[Modulation] key 59
Mod Ofs MemAFSwp 68
Main Menu (1/2) 68
[Memory] 70
(Memory Set) key 70
[Memory] key 71
4.9.4 Clearing the Memory 73
4.10 Sweep Functions 75
Main Menu (1) 76
Sweep Auxiliary 79
Output Connector 79
MG3641A/MG3642A rear panel 79
4.11 Trigger Function 81
Trigger Program 82
No Trig Program 82
Trig Input 83
4.12 Miscellaneous Functions 85
4.12.1 Setting Display On/Off 85
Chk  SysGPIB Opt Trig 86
Mod Ofs Mem 90
Data out of range 90
Error messages 90
SECTION 5 93
MEASUREMENT 93
SECTION 5 MEASUREMENT 100
Disturbing wave input level 101
SECTION 6 107
6.1.3 Setup example 108
6.1.4 Standard 109
6.2 Device Message List 110
6.2.4 Writing Commands 111
Fig. 6-2. Writing Commands 111
6.2.5 Compounding Commands 112
6.2.6 Parameter 113
6.2.7 Unit 113
6.2.8 Command Tree 114
SECTION 6 GPIB 115
6.3 Connecting the GPIB Cable 120
Program message unit 121
Numeric program data 122
Logical program data 122
Character program data 122
Suffix data (unit) 122
6.4.2 Response message format 124
6.5 Status Message 126
6.5.5 SCPI error messages 131
6.6 Initializing Device 133
6.7.1 Frequency subsystem 134
6.7.2 Output level subsystem 138
Response Level offset value 140
6.7.3 AM subsystem 144
6.7.4 FM subsystem 145
6.7.5 PM subsystem 147
6.7.7 MEMORY subsystem 151
6.7.8 Display subsystem 153
6.7.9 System subsystem 154
6.7.10 Status subsystem 155
6.8 IEEE488.2 Common Command 157
MG3641A/MG3642A 159
MS2651A spectrum analyzer 159
6.10.1 Outline 162
(3) Output level 163
SECTION 7 169
PERFORMANCE TEST 169
SECTION 7 PERFORMANCE TEST 170
7.3 Performance Test 171
7.3.1 Output frequency 172
Power meter 173
+15 to Ma-8) 174
(5) Note on test 179
SECTION 8 181
CALIBRATION 181
8.3 Calibration 182
SECTION 8 CALIBRATION 184
SECTION 9 185
STORAGE AND TRANSPORTATION 185
9.3.1 Repacking 186
9.3.2 Transportation 186
APPENDIX A 187
INITIAL FACTORY SETTINGS 187
APPENDIX B 191
FUNCTION-KEY TRANSITION 191
[Frequency offset value] 193
0.00 dB 193
APPENDIX C 197
FRONT AND REAR PANEL LAYOUT 197
APPENDIX D 201
APPENDIX D INDEX 202
3.1.1，4.4.3，4.5.3 203
APPENDIX E 207
Copy this at the measurement 212

Komentarze do niniejszej Instrukcji

Brak uwag

Anritsu MG3642A Instrukcja Użytkownika Strona 179

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Anritsu MG3642A